IC670CHS001E 现场控制平台I/O接线板

IC670CHS001E 现场控制平台I/O接线板

IC670CHS001是现场控制系列的端子板模块，以前由GE Fanuc生产，现在由艾默生自动化生产。该模块配有屏障型端子板，可容纳进出电气负载和信号装置的信号线。它提供模块化连接，因为该模块允许移除和插入托管I/O模块，而无需移除现有的接线连接。

IC670CHS001还提供背板通信，因为该模块嵌入了连接到相邻端子板模块的连接器。该端子板模块能够容纳多达两(2)个模块，支持离散I/O和模拟I/O模块。

IC670CHS001共有37个端接点。每个端子zui多可容纳两(2)根尺寸范围为#14 (2.1 mm2)至AWG #22 (0.35 mm2)的电线。适用的电线绝缘等级为90摄氏度，而推荐的紧固扭矩为8英寸-磅。对于接地端子的接线，适用的电线尺寸为AWG #14(平均2.1mm2横截面)，长度不得超过4英寸或10.16 cm。

这种接线盒模块支持水平方向DIN导轨或面板安装。通过使用IC670CHS001，当安装有适当的总线接口单元(BIU)时，特别是固件版本为2.1或更高版本的BIU模块时，可以在非危险应用区域实现热插拔。对于一个或多个终端基座的连接，使用的兼容预组装电缆为IC670CBL001。此外，辅助端子板也可以连接到该模块，以提供额外的接地、信号回路和信号公共连接。

GE Fanuc现场控制器IC670CHS001是一种屏障型接线盒，zui多可容纳现场控制模块。它支持连接到背板的模块之间的通信，并充当连接外部现场设备的端点终端。它们支持安装两个模块。这些模块通过机械方式固定在GE Fanuc IC670CHS001 I/O底座上，以避免因设备振动而意外断开。I/O基本接线板在出厂时带有保护屏障，可防止在连接或断开设备时与相邻电缆接触和短路。需要注意的重要一点是，这些模块支持电缆的连接和断开，即使模块处于通电状态。

阿格Fanuc IC670CHS001 I/O底座有37个螺丝端子。其中两个端子(标记为端子A和B)用于电源连接，其余35个用于单独的端子连接。端子可容纳AWG #14 (2.1平方毫米)至AWG #22 (0.35平方毫米)电缆。GE Fanuc IC670CHS001 I/O底座带有键，以避免额外I/O模块的错误连接。一旦这些附加模块被放置在正确的位置，通过将它们紧紧地压在底座上，就可以将它们安装到底座上。总是需要将模块的螺丝拧紧到基座上，以防止振动将模块从I/O基座上断开。制造商建议使用每英寸8至10磅的zui大扭矩。

IC670CHS001E 现场控制平台I/O接线板

The IC670CHS001 is a terminal block module in the Field Control family, formerly manufactured by GE Fanuc and now manufactured by Emerson Automation. The module is equipped with a barrier type terminal plate that accommodates signal lines to and from electrical loads and signaling devices. It provides modular connectivity as the module allows managed I/O modules to be removed and inserted without removing existing wiring connections.

The IC670CHS001 also provides backplane communication, as the module is embedded with connectors that connect to adjacent terminal board modules. The terminal board module is capable of accommodating up to two (2) modules, supporting both discrete I/O and analog I/O modules.

The IC670CHS001 has a total of 37 end points. Each terminal can accommodate up to two (2) wires in the size range #14 (2.1 mm2) to AWG #22 (0.35 mm2). The applicable wire insulation class is 90 degrees Celsius, while the recommended tightening torque is 8 inch-pounds. For ground terminal wiring, the applicable wire size is AWG #14(average 2.1mm2 cross section) and must not exceed 4 inches or 10.16 cm in length.

This junction box module supports horizontal DIN rail or panel mounting. With the IC670CHS001, hot swap can be achieved in non-hazardous application areas when the appropriate Bus interface Unit (BIU) is installed, especially BIU modules with firmware version 2.1 or higher. For the connection of one or more terminal bases, the compatible pre-assembled cable used is IC670CBL001. In addition, the auxiliary terminal board can also be connected to the module to provide additional grounding, signal loops, and signal common connections.

The GE Fanuc Field Controller IC670CHS001 is a barrier junction box that can accommodate up to a maximum of field control modules. It supports communication between modules connected to the backplane and acts as an endpoint terminal connecting external field devices. They support the installation of two modules. The modules are mechanically secured to the GE Fanuc IC670CHS001 I/O base to avoid accidental disconnection due to device vibration. The I/O base patch board comes with a protective barrier that prevents contact with adjacent cables and short circuits when connecting or disconnecting devices. An important point to note is that these modules support the connection and disconnection of cables, even when the module is powered on.

The AGFANUC IC670CHS001 I/O base has 37 screw terminals. Two of the terminals (labeled terminals A and B) are used for power connections, and the remaining 35 are used for individual terminal connections. The terminals can accommodate AWG #14 (2.1 mm ²) to AWG #22 (0.35 mm ²) cables. GE Fanuc IC670CHS001 I/O base with keys to avoid incorrect connection of additional I/O modules. Once these add-on modules are placed in the correct position, they can be mounted onto the base by pressing them tightly against the base. It is always necessary to tighten the module's screws to the base to prevent vibration from disconnecting the module from the I/O base. Manufacturers recommend a maximum torque of 8 to 10 pounds per inch.

IC670CHS001E 现场控制平台I/O接线板

雄霸售后三大保障：
质保服务一年，质量问题包退，一次合作终身VIP折扣