EMERSON A6110 双通道轴振动测量模块

EMERSON 艾默生 A6110 双通道轴振动测量模块

在I/O Builder伺服中选择伺服驱动器模块的A6110超时值驱动程序配置对话框(如"Ovation I/O Builder 用户指南"中所述)(U3-1044)或"Ovation Developer Studio”(N T-0060或W IN60)。确保这一点时间段值大于控制任务时间段的值定义与此模块关联的点。

配置寄存器(寄存器D)的第2、3和4位确定看门狗定时器。3位代码和相关的A6110时间是 Ovation I/O的标准。

zui初，计时器设置为zui长时间，即16秒。这微控制器定期读取配置寄存器并确定超时时间。

如果定时器过期，则设置内部错误LED位，并且 LED亮起。这通信正常LED熄灭。只要计时器没有过期,通信正常LED亮起，内部错误LED位被清除。
配置常量可以通过本地串行端口输入，也可以通过间接寻址A6110控制器串行接口总线上的共享内存。—个列表的命令如表22-7所示。间接寻址存储器由两个64字缓冲区组成;个用于接收数据，另个用于传输数据。 

EMERSON 艾默生 A6110 双通道轴振动测量模块

In the I/O Builder server, select the A6110 Timeout driver configuration dialog box for the server driver module (as described in the Ovation I/O Builder User Guide)(U3-1044) or the Ovation Developer Studio (N T-0060 or W IN60). Make sure that this point time period value is greater than the value of the control task time period that defines the point associated with this module.

Bits 2, 3, and 4 of the configuration register (Register D) determine the watchdog timer. The 3-digit code and associated A6110 time are the standard for Ovation I/O.

Initially, the timer was set for the maximum time, which was 16 seconds. The microcontroller periodically reads the configuration register and determines the timeout period.

If the timer expires, the internal error LED bit is set and the LED lights up. This communication is normal LED off. As long as the timer does not expire, the normal communication LED lights up and the internal error LED bit is cleared.
Configuration constants can be entered via a local serial port or indirectly addressing shared memory on the A6110 controller serial interface bus. - Table 22-7 lists the commands. The indirectly addressed memory consists of two 64-word buffers; One for receiving data and the other for transmitting data.

EMERSON 艾默生 A6110 双通道轴振动测量模块

主要产品

PLC：Allen Bradley ControlLogix，ABB DCS 800xA 模块，

GE FANUC、施耐德电气Modicon Quantum、和利时

DCS：霍尼韦尔TDC3000 CC-PDOB01，西门子MOORE，

Foxboro、Ovation、YOKOGAWA CP451-10、Emerson Epro

ESD：Invensys Triconex、HIMA DCS、本特利内华达 3500

监控系统 3500/42，ICS Triplex，伍德沃德 9907-164

型号推荐

BENTLY 125840-01 3500/15小卡    控制I/O模块
BENTLY 135489-03 3500/42M小卡    数字量输出子模件
BENTLY 135489-01 3500/42M小卡    多功能控制器
BENTLY 330130-045-00-00    数字量输入子模件
BENTLY 3500/25    控制输入输出子模件
BENTLY 149992-01 3500/33小卡    模拟量输入子模件
BENTLY 3500/34    DCS控制器模块
BENTLY 146031-01    模拟量输出子模件
BENTLY 1900/27    隔离模拟信号输入模件
BENTLY 3500/50    变频器触发板
BENTLY 3500/33    I/O扩展接口板
BENTLY 1900/65A    励磁通讯适配器
BENTLY 3500-20-01    通用电气模块
BENTLY 3500-20-01    以太网模块
BENTLY 35001513330001    火检处理器
BENTLY 35001513329201    测量板
BENTLY 3500151276100110    机器人配件
BENTLY 3500151276100100    板卡
BENTLY 35001512761001    开关量输入模块
BENTLY 3500151258400100    功率电源驱动板