SCXI-1324 高压螺钉接线端子 是 高 电压 通用 开关 应用

SCXI-1324 高压螺钉接线端子 是 高 电压 通用 开关 应用

NI SCXI-1324 （部件号： 777687-24） 是 高 电压 通用 开关 应用 的 理想 选择。该型号旨在与SCXI-1160继电器模块一起使用;它很容易安装到模块的前面。SCXI-1324是一款屏蔽式接线端子，可实现快速、轻松的信号连接。SCXI-1324高压接线端子上的48个螺丝端子与SCXI-1160继电器模块内部的16个继电器相连。与其他一些SCXI接线端子不同，该型号没有冷端传感器。SCXI 1324的共模隔离度为250 VRMS，通道间和通道间均为250 VRMS。该器件的负载或信号电流zui大为每通道 2 A。

当用户准备将NI SCXI-1324连接到SCXI-1160时，他们首先需要几个其他项目。SCXI 机箱、剪线钳、电线绝缘剥线钳、长嘴钳、1/8 英寸。需要一字螺丝刀，以及 1 号和 2 号飞利浦螺丝刀。准备好这些项目后，用户可以将模块前连接器连接到高压螺丝接线端子上的相应连接器。然后，用户可以拧紧SCXI-1324背面的顶部和底部翼形螺钉，以确保其保持在原位。

如果用户想要清洁 National Instruments SCXI 1324 接线端子，zui好先使用柔软的非金属刷子清除模型上的灰尘。用户可以使用去离子水和坚固的非金属刷清除接线端子上的其他污染物。在SCXI-1324恢复运行之前，应将其完全干燥并清除所有污染物。

SCXI-1324 的zui大场线规为 26 至 16 AWG。NI 设备 的 建议 工作 和 存储 温度 范围 分别 为 0 至 50 °C 和 –20 至 70 °C， 非冷凝 相对湿度 范围 为 5 至 90%。它的设计符合以下电气安全标准：IEC 61010-1、UL 3111-1 和 CAN/CSA C22.2 No. 1010.1。

SCXI-1324 高压螺钉接线端子 是 高 电压 通用 开关 应用

The NI SCXI-1324 (Part number: 777687-24) is ideal for high-voltage general-purpose switching applications. This model is intended for use with the SCXI-1160 relay module; It is easy to install to the front of the module. The SCXI-1324 is a shielded terminal for fast and easy signal connection. The 48 screw terminals on the SCXI-1324 high voltage terminals are connected to 16 relays inside the SCXI-1160 relay module. Unlike some other SCXI terminals, this model does not have a cold end sensor. The SCXI 1324 has a common-mode isolation of 250 VRMS, with 250 VRMS between channels and between channels. The device has A maximum load or signal current of 2 A per channel.

When users are ready to connect NI SCXI-1324 to SCXI-1160, they first need several other items. SCXI chassis, wire cutters, wire insulation strippers, long nose pliers, 1/8 inch. Flat-head screwdrivers are required, as well as size 1 and 2 Philips screwdrivers. With these items ready, the user can connect the module front connector to the corresponding connector on the high voltage screw terminal. The user can then tighten the top and bottom wing screws on the back of the SCXI-1324 to ensure that they remain in place.

If the user wants to clean the National Instruments SCXI 1324 terminals, it is best to use a soft, non-metallic brush to remove dust from the model. Users can use deionized water and a sturdy non-metal brush to remove other contaminants from the terminal. SCXI-1324 should be completely dried and all contaminants removed before resuming operation.

The SCXI-1324 has a maximum field line gauge of 26 to 16 AWG. The recommended operating and storage temperature ranges for NI devices are 0 to 50 °C and -20 to 70 °C, respectively, with a non-condensing relative humidity range of 5 to 90%. It is designed to comply with the following electrical safety standards: IEC 61010-1, UL 3111-1 and CAN/CSA C22.2 No. 1010.1.

SCXI-1324 高压螺钉接线端子 是 高 电压 通用 开关 应用