IS215UCCAM03A 是一款单插槽处理板

IS215UCCAM03A 是一款单插槽处理板

产品描述
该板（IS215UCCAM03A板）是UCCx控制器之一。UCCx控制器基于称为CompactPCI或CPCI的单板计算机。该板是通用电气生产的 Mark VIe 系统的一部分，尽管该特定型号也被认为与后来的 Mark VIeS 系统型号兼容。该型号本质上是一个IS215UCCAH3板，结合了 IS200EPMC、128 MB 闪存和 128 MB DRAM。

硬件提示和规格

IS215UCCAM03A CompactPCI是一款单插槽处理板，具有一系列独特而重要的产品规格。该板在板的前面板上有几个 LED。其中一些 LED 是;UDH 以太网状态、状态、DC、诊断、IONet 以太网和 ON LED。UDH 以太网 LED 有三种状态，有一个活动 LED 会闪烁，还有一个速度 LED，100 BaseTX 为绿色，10 Base T 为黄色。这些 LED 指示灯通常是通过中断IS215UCCAM03A的环境规格或电源要求来触发的。对于规范功能，建议在0至60摄氏度的温度下运行，理想的存储温度范围为-45至85摄氏度。该型号的湿度范围为 5% 至 95%，其工作高度为 o 至 10,000 英尺，存储高度为海拔 0 至 40,000 英尺。 在电压功率输入方面，IS215UCCAM03A需要+3.3 V dc、3.5 A（典型值）、4.25 A（zui大值）和+5 V dc（典型值）、150 mA（典型值）、300 mA（zui大额定电压）。

IS215UCCAM03A板有一系列特定的端口和协议规范，这些规范差异很大。 如下面的IS215UCCA组件图所示;EPMC 以太网接口由三个端口、一个 RJ-45 连接器和一对双绞线 10BaseT 和 100BaseTX 连接器组成。 在 EPMC 以太网接口中，有一些协议用于在 I/O 包和控制器之间进行通信;这些协议是 TCP/IP 协议。

oneport主以太网接口可处理UCCA PCB模块的许多其他协议功能。其中一种TCP/IP协议被部署用于UCCA板卡组件的控制器和工具箱之间的通信，而另一种协议则被定义为可用于与各种HMI的有效报警通信。通过使用该接口处理的其他协议包括用于与 CIMPLICITY® HMI 进行应用引导通信的 EGD 协议，以及旨在鼓励第三方 DCS 和控制器通信的 acSeries 90-70 PLC 以太网 Modbus® 协议。

IS215UCCAM03A板将至少有一个控制器和zui多四个 CPCI 机架插槽，zui多有两个电源。请注意，如果移除第 一个插槽控制器，则其余控制器将停止运行。如果任何主板需要拆卸，则必须从机架上卸下电源。有几种方法可以断开机架的电源，其中一种方法是使用远程断开开关。

IS215UCCAM03A 是一款单插槽处理板

Product description
This board (IS215UCCAM03A board) is one of the UCCx controllers. UCCx controllers are based on single-board computers called CompactPCI or CPCI. The board is part of the Mark VIe system produced by General Electric, although that particular model is also considered compatible with later Mark VIeS system models. The model is essentially an IS215UCCAH3 board that combines the IS200EPMC, 128 MB flash memory, and 128 MB DRAM.

Hardware tips and specifications

The IS215UCCAM03A CompactPCI is a single-slot processing board with a range of unique and important product specifications. The board has several leds on the front panel of the board. Some of these leds are; UDH Ethernet Status, Status, DC, Diagnostics, IONet Ethernet, and ON LED. The UDH Ethernet LED has three states, there is an active LED that will flash, and there is a speed LED, 100 BaseTX is green, 10 BaseT is yellow. These LED indicators are usually triggered by interrupting the IS215UCCAM03A's environmental specifications or power requirements. For specification functions, it is recommended to operate at temperatures between 0 and 60 degrees Celsius, with an ideal storage temperature range of -45 to 85 degrees Celsius. This model has a humidity range of 5% to 95%, and its operating altitude is o to 10,000 feet, and its storage altitude is 0 to 40,000 feet above sea level. In terms of voltage power input, the IS215UCCAM03A requires + 3.3V dc, 3.5A (typical value), 4.25A (maximum value) and + 5V dc (typical value), 150 mA (typical value), 300 mA (maximum rated voltage).

The IS215UCCAM03A board has a specific set of port and protocol specifications, which vary widely. IS215UCCA components are shown in the following figure. The EPMC Ethernet interface consists of three ports, an RJ-45 connector, and a pair of twisted pair 10BaseT and 100BaseTX connectors. In the EPMC Ethernet interface, there are protocols for communicating between I/O packets and the controller; These protocols are TCP/IP protocols.

The oneport main Ethernet interface handles many other protocol functions of UCCA PCB modules. One of the TCP/IP protocols is deployed for communication between controllers and toolboxes of UCCA board components, while the other protocol is defined as one that can be used for effective alarm communication with various Hmis. Other protocols processed by using this interface include the EGD protocol for application guidance communication with CIMPLICITY® HMI, and the acSeries 90-70 PLC Ethernet Modbus® protocol designed to encourage communication between third-party DCS and controllers.

The IS215UCCAM03A board will have at least one controller and up to four CPCI rack slots, with up to two power supplies. Note that if you remove the first slot controller, the remaining controllers will stop working. If any motherboards need to be removed, the power supply must be removed from the rack. There are several ways to disconnect the power to the rack, one of which is to use a remote disconnect switch.

IS215UCCAM03A 是一款单插槽处理板